Heating And Air Conditioning Bedford, TX

Came out for no cool. Found tstat malfunctioning wouldn't measure temperature and was unresponsive. Rebooted both outdoor and indoor units and system booted back up and is cooling

MODEL NO./RA1648AJINA SERIAL NO./W402107213 1). Condenser pad has a hole. Currently a 40x40x3, could use a 36x36 pad. 2). Condenser top panel has a hail dent. 3). Condenser fan wire grille has multiple hail dents.

System maintenance, amps on blower motor are good, drain line is clear, no water in overflow, amps are good on co.pressor and outdoor fan motor, pressures are good for temp outside, unit cooling at this time.

Checked system, was freezing over due to low r22 levels. Homeowners asked for an estimate. Worked up for trane and Lennox el17 to compete with different vendor. Financing came back declined. Homeowner will see what he can do to get the money together to fix the ac system.

I completed a job replacing a faulty pump at a local business. The pump was causing the air conditioning system to malfunction, so I replaced it with a new, energy-efficient model. The job took me a day to complete, and the client was happy with the results.

system cool maintenance. Both systems cooling efficient with no issues

Checked air flow issue. Ceiling mounted air handler that is cooling. Unable to add any dampers because of no attic space and the type of metal ductwork. Made suggestion to replace sidewall registers for bedrooms that are struggling to keep cool.

Performed ac maintenance. No failure with indoor equipment. Outdoor unit has a compressor failure. Homeowner will look over options but leaking as is. Compressor is grounded, non repairable looks to be normal wear and tear failure.

Call back. The system is one of our recent installs and the homeowner went to change the filter and was unable to do so. The filter door had some mastic holding it shut this was removed and the filter was changed. Some adjustments were also made the dampers on the unit in order to push more air to one of the further bedrooms.

Performed two system gas heating maintenance for two furnaces from 2022. Filters still clean. Furnaces in perfect condition.

Zac Preformed maintenance with all possible checks and cleanings. all readings are within range. system is clean and working properly with no errors at this time. did a final run test on system and it was running as I left.

Reached out to tech-support to try to resolve issues with existing 360 thermostat. They could not tell me why not go into the test mode. Removed thermostat and relay panel on air handler. Set up the Wi-Fi on the thermostat for Michelle. Advise her on how to Finish setting up for her Wi-Fi connection her phone.

Dispatched myself for a no cool. Equipment was recently installed in May of 2023. Thermostat was indicating that the outdoor unit was experiencing a hard lockout. I went to the outdoor unit and found no such problems on the CDA outside. Reset and system came on and is operating properly at this time.

Completed the maintenance. System is well within manufactory specifications. Cleaned condensor and checked over system. System is good at this time. See pictures.

Dispatched myself for a no cool upstairs. Upon arrival the float switch was disengaging the thermostat. Clear drain with nitrogen and system came on and is operating properly at this time.

customer wants us to come out tomorrow

Found the system to be low 2 lbs of r410a. Added the freon to the system. We will monitor the system from here. See pictures for all model and serials.

Apon arrival checked in with customer the following are my findings Found the Outside units severely dirty as well as the compressor mirroring failure as well as the TXV clock please see pictures attached to poor mccustomer about his options he would like to pursue repairs

Performed AC maintenance. checked indoor motor amps also drain for blockage, it’s clear. also confirmed low and high volt connections were tightened up, checked outdoor unit compressor amps also outdoor motor washed coils off unit working& cooling properly 20/20/4 filter was new.

When I turned power back on to indoor unit a transformer popped. I located the issue to a bad heating element on this 20 year old system . Realitor wants price on fix for this carrier upflow heating element.

Performed maintenance on both systems that we just installed. I got the temp with my temp probe and Caliberated the thermostat which was 3 degrees off . I did notice the primary condensation line after about 3 ft goes at a upwards slope and level at some parts with about five couplings from over the years . Customer said it has been draining fine and declined th repair as of now .

Gutters were clogged and iced over so when it rained again the water went right down into condenser and created thick ice that the fan blade was tapping . I removed top of unit and cleared out the ice and started the system up and it's now running to manufacture specs

Completed heat tune up form and emailed customer. They weren't feeling enough heat in bedroom so I adjusted register to allow air to blow towards the bed .

Heat pump Repair - Check refrclean condenser coclear out condensation line, Change to filter check blower motor amps and inspected duct work for any loose or damaged ducts. Also helped customer add a schedule to his thermostat and show him a few things they had questions about.

Heatpump* cleaned condenser coils , checked amp draws, found bo alerts . Made sure reversing valve was operating correctly, checked pressures , condensation line was clear and air handler still working great. 1 yr old system.